Buildup parts

[jays68yak]

I need to start a list so might as well start a build up post.

-1 3/4 DOM or HREW
-Steering column
-2wd box-Got
-pitman arm
-stock 10 bolt or d44 tierod, 2 of these would be good-Need one more.
-TBI parts-distributor, harness, sensors. (damn me for selling half my setup 2 weeks ago)
-350 parts-need a belt/pulley setup, alt-Got, power steering pump-Got
-Flywheel for a 1 piece rear main motor
-Clutch, a good used would be perfect
-Coil springs, I need 4
-350 headers, crap is ok as long as the flanges are good as I want to make my own anyways.-Got


Trying to do this on the cheap so if you have stuff in your way let me know.

[IceMan]

I need to start a list so might as well start a build up post.

-1 3/4 DOM or HREW
-Steering column
-2wd box
-pitman arm
-stock 10 bolt or d44 tierod, 2 of these would be good
-TBI parts-distributor, harness, sensors. (damn me for selling half my setup 2 weeks ago)
-350 parts-need a belt/pulley setup, alt, power steering pump
-Flywheel for a 1 piece rear main motor
-Clutch, a good used would be perfect
-Coil springs, I need 4
-350 headers, crap is ok as long as the flanges are good as I want to make my own anyways.


Trying to do this on the cheap so if you have stuff in your way let me know.

Steering column: I have a tilt, manual column and a non tilt auto. $75/$50
TBI dizzy $25
Used clutch 3 finger $25 diaphragm $40

Coils any preference? I have a bunch you can have them for $10 each
2wd box $40
SBC accessories:
alt $25
power steering pump $25
If I can find any accessory brakets you can have them.

Tilt manual, 2wd box, diaphragm clutch, coils, alt, power steering, and dizzy: $200
I also have some tierods i'll throw in.

[gokartergo]

I am pretty sure I have a 10 bolt tie rod.. I'll double check tonight.. If I do.. It is free..

[Burt4x4]

I just took off my PS pump. See it on the green box:
http://www.norcalbigdawgs.net/Gallery/albums/OneTonClub/manspace.sized.jpg
You can have it...no pully on it though?
With any luck I will be going to PacFab on Friday :unsure:

[jays68yak]

I should be going to pacfac on saturday. I have to go to some silly artichoke festival friday. :uh oh:

[Nosmog73]

I have a flywheel that will need to be cleaned..How do you know if it came off a one piece seal..

If it can be used you can have it..

[jays68yak]

I have a flywheel that will need to be cleaned..How do you know if it came off a one piece seal..

If it can be used you can have it..

Production small-block V8 and V6/90-degree Chevrolet crankshafts were redesigned in 1986 to use a leak-resistant one-piece rear seal. The diameter of the crankshaft flywheel flange was reduced to fit this new seal. The engine block, oil pan, pan gaskets, and flywheel were also redesigned to accommodate this one-piece seal.
Crankshafts designed for one-piece seals have a smaller flywheel bolt pattern than pre-1986 production cranks. All small-block and V6/90-degree cranks which use a one-piece seal require a counterweighted flywheel for proper engine balance.

So we would need to compair bolt circles. But I dont have the motor yet.

[k5LS2]

I have tons of coils for you as well as a tilt GM steering colume with a green 3 spoke grant wheel :D Also have the frame from the 91 burb with brake stuff and a set of 1/2 ton sticks (parts for the ones you have). I think theres a clutch floating around here as well. Also I have A few Drive shafts you could have and a electric fan or two, a choice of radiators plenty of wire and plugs and stuff :2thumbs: All yours for FREE,

Come on guys, lets see How little jaysak can build this thing for!!! Dude, I have tons of hoses and fittings ect just ask!!

[jays68yak]

I have tons of coils for you as well as a tilt GM steering colume with a green 3 spoke grant wheel :D Also have the frame from the 91 burb with brake stuff and a set of 1/2 ton sticks (parts for the ones you have). I think theres a clutch floating around here as well. Also I have A few Drive shafts you could have and a electric fan or two, a choice of radiators plenty of wire and plugs and stuff :2thumbs: All yours for FREE,

Come on guys, lets see How little jaysak can build this thing for!!! Dude, I have tons of hoses and fittings ect just ask!!

Ill trade you labor for your parts. You know I dont like just taking stuff from you.

[Nosmog73]

When you get the motor give me a holler and I can measure it..its yours for free if you can use it... :2thumbs:

[4X4HIGH]

The bolt circle for the flywheel will be a 3.48" inch if it is 1985 and earlier and 3.00" if it is 1986 and later.

[stunnin650]

i have front coils out of that xj and all of the big ass heims and the two sticks of 1.50 .380 dom tube, and i will try to get the hyd set up on the bender

[jays68yak]

i have front coils out of that xj and all of the big ass heims and the two sticks of 1.50 .380 dom tube, and i will try to get the hyd set up on the bender

If not I can use the work out. Well just mount it to the garage floor.

[Twisted Whipz]

well not sure but i have the older headers from my 406 sbc $30
and i think i still have the d44 tie-rod from the trussed axle yours if i still have it

[BamBamK5]

i have a complete serpintine belt set u with the alt, power steering pump and pulleys. how bout 100 for all.

[barbastard]

I think I've got an alternator lying around my garage. I've got to clean up the garage this weekend. If if find it, it's yours. You can get it next weekend from me.