To Do List...

[crewcabroller]

To Do List for hollister:

-Make new links for rear - DONE
-Make new rear drive shaft
-Replace water pump
-Replace power steering pump that runs the brakes
-Replace oil pan
-Fix ground on power steering cooling fan

:crazy:

Tomorrow's pretty much my last day so it's going to be a long one after work...

[stunnin650]

put the air filter housing it and plumb it
maybe redo the shock mounts
tie up wiring
cable clamps on the battery cable from the back to the front
and other stuff i can't remember

[jays68yak]

ummm top off the tranny and tcase.
get it out of the garage and load it.

haha :flipoff2:

figured I dont need a skid plate with the tcase being so far up and the only rocks being the ones at sqeeze rock.

[k5LS2]

.1 get gas :thumb:

[k5krushert1]

get started on my new project rig :D

[Ryan B.]

Finish oil pan skidplate.
Change cracked bushings on front shackles.
Torque a few things again.
Finish a little bit of wiring and loom it.
Bolt in passanger seat.
Pack.
Get Gas.

[Nosmog73]

So what is the TO DO list for the hammers.. :thumb:

[Twisted Whipz]

nah, we're going to hh this weekend. 6-8 of jan

[Twisted Whipz]

are you gonna get out there and see the maylay that insues. mud+rocks+trucks=fun

[CaptainInsano]

Nothin...cause I can't go. :(

[jays68yak]

Nothin...cause I can't go. :(

no yota? :(

[Hoss]

#1 buy ps fluid
#2 pack supplys


hopefully by 6 pm ill be there

[jays68yak]

So when is everyone showing up? Jason do we need to save you a bigger spot this time?

[CaptainInsano]

Nothin...cause I can't go. :(

no yota? :(

It's technically my roommate John's truck, we just recently asked him to move out and he was not too happy with the new look of his truck when it returned last time. :rolleyes: Plus I have no trailer to get it down there, and I personally think it is ready to blow up and I don't want to be the one driving it when it does. I need a trailer damn it. :letitout: I'll see if I can talk him into it. :beer:

[jays68yak]

oh time to have the house to you anre your lady only?

[CaptainInsano]

oh time to have the house to you anre your lady only?

Yup, its about damn time. :beer: :beer: :beer:

[PaloAltoK5]

It's technically my roommate John's truck, we just recently asked him to move out and he was not too happy with the new look of his truck when it returned last time. :rolleyes:

Heh, give it a bath, I'll run by kragen and get a crap load of that redish brown primer. It'll only take an hour or two to re-paint the whole friggin truck, it'll look the best it has since HE rolled and then he can quit his friggin whinning!!

[CaptainInsano]

It's technically my roommate John's truck, we just recently asked him to move out and he was not too happy with the new look of his truck when it returned last time. :rolleyes:

Heh, give it a bath, I'll run by kragen and get a crap load of that redish brown primer. It'll only take an hour or two to re-paint the whole friggin truck, it'll look the best it has since HE rolled and then he can quit his friggin whinning!!

Can't blame him, I wouldn't let me drive my truck either. :unsure:

[CaptainInsano]

Why there's no more driver window...

http://www.silverlegend.biz/wheelin/DSC02415.JPG

Then of course why the door does not even open or close anymore...

http://www.silverlegend.biz/wheelin/Hollister December 2005 103.jpg

That said I'm working on getting him to let me right take it right now...

[jays68yak]

dude did oyu make it up that? Ive wanted to try that for a while in my blazer.

[PaloAltoK5]

Jay, yeah, he did, friggin perfect line too, an inch either direction and he would been on his side wedged in there!! There are more pics of the attempt on my site too...

However, the entrance is so tight it even popped a side window in the Toyota, I couldn't even get past the tree roots with the blazer...

[PaloAltoK5]

http://www.silverlegend.biz/wheelin/DSC02413.JPG

http://www.silverlegend.biz/wheelin/DSC02414.JPG

The perfect line out:
http://www.silverlegend.biz/wheelin/Hollister%20December%202005%20043.jpg

[CaptainInsano]

dude did oyu make it up that? Ive wanted to try that for a while in my blazer.

I tried it in my Blazer once, didn't work out so well. :crazy:

It's also why I now have a lexan windshield. :) But did make it in the Yota, that damn nub on the tree gets ya everytime.

I actually drove out of this shit, only help from my buddy Tom, emotional support from Steph, and a Quadrajet that runs at a 90 degree angle.

[Twisted Whipz]

thats the hole where jerry lost his windshied to the root. sweet

[crewcabroller]

So when is everyone showing up? Jason do we need to save you a bigger spot this time?

That spot actually worked really well, just make sure no one parks in there... The trash can might not be so happy again though... Or maybe I just shouldn't let a drunk guy spot me into my spot at midnight :flipoff2:

[PaloAltoK5]

Hmm..now that it's over, what on everybody's to do list for Feb?? Ha-ha :thumb:

[crewcabroller]

Uh basically everything that I put on my list in the first post since I never did any of it other than the shaft and link.

[jays68yak]

build a new truck right after my money tree grows.

[PaloAltoK5]

build a new truck right after my money tree grows.

Haha, let me know what kind of seeds and fertilizer for that one, I need one too!!

My list:

Finish Hacking and tubing the front.
Hack my bumper to match
Move my front axle 1.5" forward
Pick-up/go through/rebuild/install my new th400
Install my Chromoly front axels and new CTM's
Finish installing the Hydro assist (i.e. tap the box, weld the tabs, blah blah)
Repair/remove or replace the non-fuctioning passenger door...
Maybe swap some Lexan window for the glass one in the top..
There's more, but since I am in Asia :blink: I'll have to look over the rig more when I get home.

Hey, at least I fixed that damn leaking rear diff cover, changed all the fluids and removed most of the steering for the Hydro install before I left!! :thumb:

[crewcabroller]

Oh yeah, need to replace the windshield. Not being able to see out of mine caused a a little undue stress for Kevin :rolleyes: :D I believe he got most of his frustration out while playing demo derby with my truck :p

[barbastard]

Or maybe I just shouldn't let a drunk guy spot me into my spot at midnight :flipoff2:

Hey….now…..don’t be knocking my guiding skills….I did a great job. Oh…and by the way….I wasn’t “drunk”…I was wasted!!! And it was closer to 11:30 than midnight!!! :flipoff2:



My to Do list (for anyone that cares):

1.Install electric fan and run power/control wires for it.
2.Order and install new HD tierod and weld new mounts on it for ram
3.Install new KRC PS pump, reservoir and hoses
4.Fab and install new passenger side front shock mount.
5.Build 1.75” DOM roll cage with integrated seat mounts
6.Hack more sheet metal up
7.Install new tranny kickdown cable
8.Fab up spare rear d-shaft
9.Re-route vent lines up higher
10.Install 2 more rock lights.

[CaptainInsano]

build a new truck right after my money tree grows.

Haha, let me know what kind of seeds and fertilizer for that one, I need one too!!

My list:

Finish Hacking and tubing the front.
Hack my bumper to match
Move my front axle 1.5" forward
Pick-up/go through/rebuild/install my new th400
Install my Chromoly front axels and new CTM's
Finish installing the Hydro assist (i.e. tap the box, weld the tabs, blah blah)
Repair/remove or replace the non-fuctioning passenger door...
Maybe swap some Lexan window for the glass one in the top..
There's more, but since I am in Asia :blink: I'll have to look over the rig more when I get home.

Hey, at least I fixed that damn leaking rear diff cover, changed all the fluids and removed most of the steering for the Hydro install before I left!! :thumb:

Install my Chromoly front axels and new CTM's Maybe actually get it done this year???? or are you going to bring them in the box to Reno again??? :flipoff2:

[PaloAltoK5]

build a new truck right after my money tree grows.

Haha, let me know what kind of seeds and fertilizer for that one, I need one too!!

My list:

Finish Hacking and tubing the front.
Hack my bumper to match
Move my front axle 1.5" forward
Pick-up/go through/rebuild/install my new th400
Install my Chromoly front axels and new CTM's
Finish installing the Hydro assist (i.e. tap the box, weld the tabs, blah blah)
Repair/remove or replace the non-fuctioning passenger door...
Maybe swap some Lexan window for the glass one in the top..
There's more, but since I am in Asia :blink: I'll have to look over the rig more when I get home.

Hey, at least I fixed that damn leaking rear diff cover, changed all the fluids and removed most of the steering for the Hydro install before I left!! :thumb:

Install my Chromoly front axels and new CTM's Maybe actually get it done this year???? or are you going to bring them in the box to Reno again??? :flipoff2:

Oh yeah good point, one more thing on my to do list:
-Get my spindle nut socket from Mark..... :thumb: :flipoff2: